How to Attach the VANGUARD Missile Launcher Add-On Safely
By Valaverse | Published: 2026-10-14
Category: How-to Guides
A step-by-step guide to mounting the VANGUARD Missile Launcher Add-On without stressing the turret or losing small parts. Includes fit checks, blast-effect setup, and display tips.
Quick answer
To attach the VANGUARD Missile Launcher Add-On safely, first confirm the turret ring is clear, then seat the launcher base fully before pressing down. Load the 12 non-firing missiles after the launcher is locked in place, and keep the 3 blasting missiles and rear blast effect for final display. Always test the upward firing position with an empty launcher to avoid bending the mount.
Check compatibility and clear the turret ring
The VANGUARD Missile Launcher Add-On is designed to fit all Action Force Vanguard vehicles, but that does not mean every vehicle is ready out of the box. Before you attach anything, remove any existing turret accessories, figures, or debris from the mounting point. A partially seated previous add-on can block the new launcher from clicking down fully. If you are switching between the Stealth Gray and Desert Tan versions, do one at a time and keep the unused missiles in a small tray so they do not roll under furniture.
Seat the launcher base before loading missiles
Place the launcher turret onto the vehicle mount and press straight down until you feel it stop. Do not twist or force it; the launcher is designed to sit in a specific orientation. Once the base is seated, you can rotate the turret to the upward firing position. This is the moment to check for wobble. A launcher that rocks side to side is not fully seated and will not hold the upward angle reliably. Only after the base is secure should you load the 12 non-firing missiles. Loading first adds weight that can make a partial connection feel tighter than it is, leading to a false sense of security.
Place blasting missiles and rear blast effect last
The set includes three blasting missiles in different sizes and one rear blast effect. These are display pieces, not firing projectiles, and they are best added after the launcher is mounted and the non-firing missiles are loaded. The rear blast effect fits at the back of the launcher and can interfere with the turret rotation if you attach it before setting the upward angle. Decide on your final pose first, then add the blast effect. If you plan to move the vehicle often, remove the blasting missiles and blast effect before transport; they are the easiest pieces to lose or snap.
Pair with the H.A.U.L. accessory set for a full build
If you are also adding the VANGUARD H.A.U.L. Muddy Tan Accessory Set, install the windowless doors and armored panels before the missile launcher. The H.A.U.L. set includes a brush guard and cow catcher that fit onto the bumper, and the cow catcher can sit on top of the brush guard. These front-end parts do not block the turret, but they change the vehicle's balance. A heavier front end can make a top-heavy missile launcher feel less stable on a shelf. Add the H.A.U.L. parts first so you can test the vehicle's center of gravity, then mount the launcher and adjust the upward angle to compensate.
Step-by-step installation
- Clear the turret mount: Remove any existing turret add-on, figure, or loose part from the mounting point. Wipe the area with a dry cloth if it is dusty. Checkpoint: the mount should be flat and free of obstructions before you introduce the new launcher.
- Test-fit the launcher base: Lower the launcher onto the mount without forcing it. It should sit flush. If it rocks, lift it and check for a misaligned tab or debris. Common mistake: pressing down on one side only, which can bend the mount. Press evenly with two fingers.
- Rotate to the upward firing position: With the base seated, gently rotate the turret upward until it stops. Do not over-rotate; the launcher is designed to hold a specific angle. Checkpoint: the turret should stay in place when you let go. If it droops, reseat the base.
- Load the 12 non-firing missiles: Insert each missile into its tube until it sits flush. Count as you go so you do not leave one half-seated. Common mistake: forcing a missile that does not slide easily. If it binds, rotate it slightly and try again.
- Add the blasting missiles and rear blast effect: Choose the blasting missile size that matches your display pose, then attach the rear blast effect at the back of the launcher. Checkpoint: the blast effect should not touch the turret rotation path. Adjust if it rubs.
- Do a stability check: Lift the vehicle gently and tilt it side to side. The launcher should not shift or rattle. If it does, remove the missiles and reseat the base. Next step: if you are also using the H.A.U.L. set, install those parts first on your next build to avoid redoing the turret.
Product facts
- VANGUARD Stealth Gray Missile Launcher Add-On: Action Force VANGUARD Missile Launcher Add-On Accessory Set fits all Action Force Vanguard vehicles and includes 12 non-firing missiles, 3 blasting missiles in different sizes, and 1 rear blast effect. You get enough missiles for a full loadout plus display effects, but you need to keep the non-firing and blasting pieces separate during setup to avoid mixing them up.
- VANGUARD Desert Tan Missile Launcher Add-On: The Desert Tan version carries the same contents: 12 non-firing missiles, 3 blasting missiles, and 1 rear blast effect, with a launcher turret that can be put in an upward firing position. Color choice does not change the installation steps, so you can follow the same process whether you picked Stealth Gray or Desert Tan.
- VANGUARD H.A.U.L. Muddy Tan Accessory Set: The VANGUARD H.A.U.L. Muddy Tan Accessory Set includes 4 windowless doors, 4 armored panels that fit into the doors, 2 additional armored frames for rear doors that can hold the M240 rifle (not included), a windshield armor add-on, a brush guard that fits onto the bumper, and a cow catcher that fits onto the bumper or on top of the brush guard. These parts add front and side protection that can shift the vehicle's balance, so install them before the missile launcher to keep the turret stable.
